Import xPack OpenOCD 0.12.0-7 and GNU Make 4.4.1 from x86_64-w64-mingw32.

2026-09-14 16:20:05 +08:00
parent 2b73c30a9d
commit 534c017e0f
1133 changed files with 74341 additions and 0 deletions
@@ -0,0 +1,85 @@
+# SPDX-License-Identifier: GPL-2.0-or-later
+
+#
+# script for Atmel SAMD, SAMR, SAML or SAMC, a Cortex-M0 chip
+#
+
+#
+# samdXX devices only support SWD transports.
+#
+source [find target/swj-dp.tcl]
+
+if { [info exists CHIPNAME] } {
+   set _CHIPNAME $CHIPNAME
+} else {
+   set _CHIPNAME at91samd
+}
+
+if { [info exists ENDIAN] } {
+   set _ENDIAN $ENDIAN
+} else {
+   set _ENDIAN little
+}
+
+# Work-area is a space in RAM used for flash programming
+# By default use 2kB
+if { [info exists WORKAREASIZE] } {
+   set _WORKAREASIZE $WORKAREASIZE
+} else {
+   set _WORKAREASIZE 0x800
+}
+
+if { [info exists CPUTAPID] } {
+   set _CPUTAPID $CPUTAPID
+} else {
+   set _CPUTAPID 0x4ba00477
+}
+
+swj_newdap $_CHIPNAME cpu -irlen 4 -expected-id $_CPUTAPID
+dap create $_CHIPNAME.dap -chain-position $_CHIPNAME.cpu
+
+set _TARGETNAME $_CHIPNAME.cpu
+target create $_TARGETNAME cortex_m -endian $_ENDIAN -dap $_CHIPNAME.dap
+
+$_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE -work-area-backup 0
+
+# SAMD DSU will hold the CPU in reset if TCK is low when RESET_N
+# deasserts (see datasheet Atmel-42181E–SAM-D21_Datasheet–02/2015, section 12.6.2)
+#
+# dsu_reset_deassert configures whether we want to run or halt out of reset,
+# then instruct the DSU to let us out of reset.
+$_TARGETNAME configure -event reset-deassert-post {
+        at91samd dsu_reset_deassert
+}
+
+# SRST (wired to RESET_N) resets debug circuitry
+# srst_pulls_trst is not configured here to avoid an error raised in reset halt
+reset_config srst_gates_jtag
+
+# Do not use a reset button with other SWD adapter than Atmel's EDBG.
+# DSU usually locks MCU in reset state until you issue a reset command
+# in OpenOCD.
+
+# SAMD runs at SYSCLK = 1 MHz divided from RC oscillator after reset.
+# Other members of family usually use SYSCLK = 4 MHz after reset.
+# Datasheet does not specify SYSCLK to SWD clock ratio.
+# Usually used SYSCLK/6 is slow, testing shows that debugging can
+# work @ SYSCLK/2 but your mileage may vary.
+# This limit is most probably imposed by incorrectly handled SWD WAIT
+# on some SWD adapters.
+
+adapter speed 400
+
+# Atmel's EDBG (on-board cmsis-dap adapter of Xplained kits) works
+# without problem at maximal clock speed. Atmel recommends
+# adapter speed less than 10 * CPU clock.
+# adapter speed 5000
+
+if {![using_hla]} {
+   # if srst is not fitted use SYSRESETREQ to
+   # perform a soft reset
+   cortex_m reset_config sysresetreq
+}
+
+set _FLASHNAME $_CHIPNAME.flash
+flash bank $_FLASHNAME at91samd 0x00000000 0 1 1 $_TARGETNAME